Fuers TL-2600 Fake Camera Instruction Manual

1. उत्पादन समाप्तview

The Fuers TL-2600 is a high-quality, durable dummy surveillance camera designed to deter potential intruders. It features a realistic appearance, a flashing LED light, and is suitable for both indoor and outdoor use. This device provides a cost-effective solution to enhance security visibility without the complexity of a real surveillance system.

मुख्य विशेषताहरु:

• यथार्थवादी डिजाइन: High resemblance to actual security cameras.
• फ्ल्यासिङ एलईडी बत्ती: Simulates active surveillance, powered by 2 AAA batteries (not included).
• टिकाउ निर्माण: Made from high-quality ABS material, weather-resistant for outdoor use.
• समायोज्य कोण: Features a mounting bracket allowing for 90° vertical and 360° horizontal rotation.
• सजिलो स्थापना: No wiring required, mounts quickly to walls or ceilings.

Image 1.1: The Fuers TL-2600 Fake Camera featuring a red flashing LED light, simulating active operation.

Image 1.2: The camera's adjustable bracket allows for 90-degree vertical and 360-degree horizontal rotation for optimal positioning.

2. प्याकेज सामग्री

कृपया तल सूचीबद्ध सबै वस्तुहरू तपाईंको प्याकेजमा समावेश छन् भनी प्रमाणित गर्नुहोस्:

• 1 x Fuers TL-2600 Dummy Camera Unit
• 1 x Mounting Bracket (pre-attached)
• ४ x माउन्टिङ स्क्रू
• X x भित्ता प्लगहरू
• 1 x CCTV Warning Sticker

नोट: 2 x AAA batteries are समावेश छैन र छुट्टै खरिद गर्नुपर्छ।

Image 2.1: Contents of the package including the dummy camera, mounting hardware, and a CCTV sticker. Dimensions are also shown.

3. सेटअप

3.1 ब्याट्री स्थापना

1. Locate the battery compartment on the underside of the camera body.
2. डिब्बाको कभर सावधानीपूर्वक खोल्नुहोस्।
3. सही ध्रुवता (+/-) सुनिश्चित गर्दै, डिब्बामा दुई (२) AAA ब्याट्रीहरू (समावेश नगरिएका) घुसाउनुहोस्।
4. Close the battery compartment cover securely. The LED light should begin flashing immediately.

छवि १: View of the battery compartment opened to insert two AAA batteries.

Image 3.2: Step-by-step guide for installing batteries into the dummy camera.

3.2 क्यामेरा माउन्ट गर्दै

1. Choose a suitable location for installation, such as a wall or ceiling, ensuring good visibility and deterrence.
2. Position the mounting bracket at the desired location and mark the three screw holes.
3. Drill pilot holes at the marked spots. For masonry or drywall, insert the provided wall plugs.
4. प्रदान गरिएको स्क्रू प्रयोग गरेर माउन्टिङ कोष्ठकलाई सतहमा सुरक्षित गर्नुहोस्।
5. Adjust the camera angle as needed (refer to Section 4.1).
6. Affix the included CCTV warning sticker in a prominent location nearby to further enhance deterrence.

4. सञ्चालन निर्देशनहरू

३.१ क्यामेरा कोण समायोजन

The camera's mounting bracket allows for flexible positioning:

• ठाडो समायोजन: Loosen the side screw on the bracket to tilt the camera up or down (up to 90°). Tighten the screw once the desired angle is achieved.
• तेर्सो समायोजन: The base of the bracket allows for full 360° rotation. Simply rotate the camera body to face the desired direction.

4.2 एलईडी फ्ल्यासिंग

Once batteries are correctly installed, the red LED light will automatically begin to flash continuously. There is no separate on/off switch for the LED. The flashing LED simulates the operation of a real security camera, enhancing its deterrent effect.

5. मर्मतसम्भार

• ब्याट्री प्रतिस्थापन: Replace the two AAA batteries when the LED light stops flashing or becomes dim. Always use fresh batteries for optimal performance.
• सरसफाई: Wipe the camera body and lens area with a soft, damp धुलो र फोहोर हटाउन कपडा। कठोर रसायन वा घर्षण क्लीनर प्रयोग नगर्नुहोस्।
• मौसम प्रतिरोध: While designed for outdoor use, extreme weather conditions (e.g., heavy storms, prolonged direct sunlight) may affect its lifespan. Periodically check the unit for any signs of wear or damage.

T. समस्या निवारण

• LED Not Flashing:
  • ब्याट्रीहरू सही ध्रुवताका साथ सही तरिकाले स्थापना गरिएका छन् कि छैनन् जाँच गर्नुहोस्।
  • नयाँ AAA ब्याट्रीहरूसँग बदल्नुहोस्।
• Camera Feels Loose After Mounting:
  • सबै माउन्टिङ स्क्रूहरू सुरक्षित रूपमा कसिएको सुनिश्चित गर्नुहोस्।
  • If mounted on drywall, ensure wall plugs are properly seated.

7. निर्दिष्टीकरणहरू