BWI EAGLE 10-7140 इन्डक्टिव प्रोक्सिमिटी टाइप प्रोक्स सेन्सर
निर्देशनहरू प्रयोग गरेर उत्पादन
- Select the roller or shaft to be monitored. Ensure the roller is always in contact with the belt.
- Affix a target (e.g., key-stock, 1/4-20 Hex Nut) on the roller or shaft. Do not use notches or dents as targets.
- होज क्ल्याम्प प्रयोग गरेर सेन्सरलाई बलियोसँग माउन्ट गर्नुहोस्।amps or U-bolts to prevent movement. Do not use tape as a fastener.
- Position the target so that it passes through the centre area of the sensor face for optimal sensitivity and sensing distance.
- Check that the LED on the sensor blinks proportionally to the speed of the shaft or roller when moved toward the target.
- The effective distance between the sensor and target ranges from approximately .1 inch to .5 inch based on target size.
प्रोक्स सेन्सर
- आगमनात्मक निकटता प्रकार
- मॉडल -10 7140-१-XNUMX१२
स्थापना
- Select the roller or shaft to be monitored. If a roller is to be monitored, be sure it is always contacting the belt.
- Affix a target on the roller or shaft. The target should be a piece of key-stock, 1/4-20 Hex Nut, etc. (Figure 1) NOTE: The use of a notch or a dent is not an acceptable target for the prox sensor. This sensor must see the presence of a target, not an absence of a target as there would be with a notch or dent.
- Mount the sensor firmly with hose clamps वा U-बोल्टहरू चल्न वा खुकुलो काम गर्नबाट रोक्नको लागि। टेपलाई फास्टनरको रूपमा सिफारिस गरिँदैन।
- Before tightening, check that the target passes through the centre area of the sensor face. This will produce the greatest sensitivity and sensing distance.
With the roller or shaft spinning, move the sensor toward the target. The LED on the sensor should blink in direct proportion to the speed of the shaft or roller.
The effective distance between the sensor and target is approximately .1 inch to .5 inch, depending on the size of the target.
नोट: When mounting a sensor on small idler rollers (less than 6 inches in diameter), install a maximum of 2 targets.
निर्दिष्टीकरणहरू
| 10-7140 निर्दिष्टीकरणहरू | |
| आयामहरू | ४.१२ इन्च x १.३७ इन्च ओडी |
| सेन्सर प्रकार | आगमनात्मक निकटता (धातु) |
| आवास | १ ३/८″ १२ TPI थ्रेडेड एल्युमिनियम |
| सेन्सर पावर आवश्यकता | नियन्त्रण एकाइबाट हालको सीमित १२VDC |
| युनिट सेन्सर केबल | Unshielded ** Twisted Pair 16/2 – 3 Ft. Pigtail |
| दूरी | सेन्सर टु कन्ट्रोल युनिट – २ माइल |
| न्यूनतम सेन्सिङ गति | १ RPM भन्दा कम |
नोट – Shielded cable is recommended for all above-ground applications. The shield of the cable should be attached to earth ground within 2 feet of the sensor head. In severe noise environments, grounding the shield at the control
module also, will also eliminate any E.M.I. interference.
सम्पर्क गर्नुहोस्
- १०५ बोनी ड्राइभ
- बटलर, PA १६००२
- ८००-५५५-०१९९
- फ्याक्स ८००-५५५-०१९९
- www.bwieagle.com मा
FAQ
प्रश्न: के म प्रोक्स सेन्सरको लागि लक्ष्यको रूपमा खाच वा डेन्ट प्रयोग गर्न सक्छु?
A: No, the sensor must detect the presence of a target, not an absence of a target like with a notch or dent.
प्रश्न: जमिन माथिको अनुप्रयोगहरूको लागि सिफारिस गरिएको केबल के हो?
A: Shielded cable is recommended, and its shield should be attached to earth ground within 2 feet of the sensor head. In noisy environments, grounding the shield at the control module can eliminate E.M.I. interference.
कागजातहरू / स्रोतहरू
 |
BWI EAGLE 10-7140 इन्डक्टिव प्रोक्सिमिटी टाइप प्रोक्स सेन्सर [pdf] निर्देशन पुस्तिका १०-७१४०, १०-७१४० इन्डक्टिभ प्रोक्सिमिटी टाइप प्रोक्स सेन्सर, इन्डक्टिभ प्रोक्सिमिटी टाइप प्रोक्स सेन्सर, प्रोक्सिमिटी टाइप प्रोक्स सेन्सर, टाइप प्रोक्स सेन्सर, प्रोक्स सेन्सर |