M5StickC Plus2 Operation Guidance
कारखाना फर्मवेयर
When the device encounters operational issues, you can try re-flashing the factory firmware to check if there is any hardware malfunction. Refer to the following tutorial. Use the M5Burner firmware flashing tool to flash the factory firmware onto the device.
FAQ
Q1: Why is my M5StickC Plus2 black screen/won’t boot?
समाधानहरू: M5Burner Burn official Factory Firmware“M5StickCPlus2 User Demo”
Q2: Why it working time only 3 hours? Why does it 100% charge in 1 minute, remove the charging cable it will turn off?
Solutions: “Bruce for Stack plus2”This is an unofficial firmware. Flashing unofficial firmware can void your warranty, cause instability, and expose your device to security risks. Proceed with caution.
Please burn back official firmware.
तयारी
- Refer to the M5Burner tutorial to complete the firmware flashing tool download, and then refer to the image below to download the corresponding firmware.
डाउनलोड लिङ्क: https://docs.m5stack.com/en/uiflow/m5burner/intro
USB चालक स्थापना
Driver Installation Tip
Click the link below to download the driver matching your operating system. The driver package for the CP34X (for the CH9102 version) can be downloaded and installed by selecting the installation package corresponding to your operating system. If you encounter issues with program download (such as timeout or “Failed to write to target RAM” errors), try reinstalling the device driver.
CH9102_VCP_SER_Windows
https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_SER_Windows.exe
CH9102_VCP_SER_MacOS v1.7
https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_MacOS_v1.7.zip
Port Selection on MacOS
On MacOS, there may be two available ports. When using them, please select the port named wchmodem.
पोर्ट चयन
Connect the device to the computer via a USB cable. After the driver installation is complete, you can select the corresponding device port in M5Burner.
जलाउनुहोस्
Click “Burn” to start the flashing process.
StickC-Plus2
SKU:K016-P2
विवरण
StickC-Plus2 is the iterative version of Stick C-Plus. It is powered by the ESP32-PICO-V3-02 chip, providing Wi-Fi connectivity. Within its compact body, it integrates a rich variety of hardware resources, including IR emitter, RTC, microphone, LED, IMU, buttons, buzzer, and more. It features a 1.14-inch TFT display driven by the ST7789V2 with a resolution of 135 x 240.
The battery capacity has been increased to 200 mAh, and the interface is compatible with both HAT and Unit series modules.
This sleek and compact development tool can ignite unlimited creativity. StickC-Plus2 helps you quickly build IoT product prototypes and greatly simplifies the entire development process. Even beginners who are new to programming can create interesting applications and apply them in real life.
ट्यूटोरियल
UIFlow
This tutorial will introduce how to control the StickC-Plus2 device through the UIFlow graphical programming platform.
UiFlow2 ले तपाईंलाई 100% सहयोग गर्नेछ।
This tutorial will introduce how to control the StickC-Plus2 device through the UiFlow2 graphical programming platform.
Arduino IDE
This tutorial will introduce how to program and control the StickC-Plus2 device using the Arduino IDE.
नोट
Port Not Recognized
When using a C-to-C cable, if the port cannot be recognized, please perform the following power-on procedure:
disconnect StickC-Plus2, power it off (long-press the power button until the green LED lights up), then reconnect the USB cable to power on.
सुविधाहरू
- Based on ESP32-PICO-V3-02 with Wi-Fi support
- Built-in 3-axis accelerometer and 3-axis gyroscope
- Integrated IR emitter
- Built-in RTC
- एकीकृत माइक्रोफोन
- User buttons, 1.14-inch LCD, power/reset button
- 200 mAh लि-आयन ब्याट्री
- विस्तार कनेक्टर
- Integrated passive buzzer
- Wearable & mountable
- विकास प्लेटफर्म
- UiFlow1 ले तपाईंलाई 100% सहयोग गर्नेछ।
- UiFlow2 ले तपाईंलाई 100% सहयोग गर्नेछ।
- Arduino IDE
- ESP-IDF
- प्लेटफर्म आईओ
समावेश गर्दछ
- 1 x StickC-Plus2
अनुप्रयोगहरू
- पहिरन योग्य उपकरणहरू
- IoT controller
- STEM education
- DIY परियोजनाहरू
- स्मार्ट-होम उपकरणहरू
निर्दिष्टीकरणहरू
| निर्दिष्टीकरण | प्यारामिटर |
| SoC | ESP32-PICO-V3-02 240 MHz dual-core, Wi-Fi, 2 MB PSRAM, 8 MB Flash |
| इनपुट भोल्यूमtage | 5 V @ 500 mA |
| इन्टरफेस | Type-C x 1, GROVE (I2C + I/O + UART) x 1 |
| एलसीडी स्क्रिन | 1.14 inch, 135 x 240 Color TFT LCD, ST7789V2 |
| माइक्रोफोन | SPM1423 |
| बटनहरू | User buttons x 3 |
| एलईडी | Green LED x 1 (non-programmable, sleep indicator) Red LED x 1 (shares control pin G19 with IR emitter) |
| RTC | BM8563 |
| बजर | On-board passive buzzer |
| IMU | MPU6886 |
| एन्टेना | 2.4 G 3D antenna |
| बाह्य पिनहरू | G0, G25/G26, G36, G32, G33 |
| ब्याट्री | 200 mAh @ 3.7 V, inside |
| सञ्चालन तापमान | ० ~ ६० डिग्री सेल्सियस |
| घेरा | प्लास्टिक (पीसी) |
| उत्पादन आकार | २०४ x ६४ x ८० मिमी |
| उत्पादन वजन | 16.7 ग्राम |
| प्याकेज साइज | २०४ x ६४ x ८० मिमी |
| सकल वजन | 26.3 ग्राम |
सञ्चालन निर्देशनहरू
पावर अन/अफ
Power-on: Press the “BUTTON C” for more than 2 seconds, or wake up via the RTC IRQ signal. After the wake-up signal is triggered, the program must set the HOLD pin (G4) to high (1) to keep the power on, otherwise the device will shut down again.
Power-off: Without external USB power, press “BUTTON C” for more than 6 seconds, or set HOLD (GPIO4)=0 in the program to power off. While USB is connected, pressing “BUTTON C” for more than 6 seconds will turn off the screen and enter sleep mode (not a full power-off).
योजनाबद्ध
पिन नक्शा
Red LED & IR Emitter | Button A | Button B | Buzzer
| हामीसँग अहिले स्टकमा ESP32-PICO-V3-02 को 250 टुक्राहरू उपलब्ध छन्। | GPIO19 | GPIO37 | GPIO39 | GPIO35 | GPIO2 |
| IR Emitter & Red LED | IR emitter & Red LED pin | ||||
| बटन ए | बटन ए | ||||
| बटन B | बटन B | ||||
| बटन C | बटन C | ||||
| निष्क्रिय बजर | बजर |
रंग TFT प्रदर्शन
Driver IC: ST7789V2
रिजोल्युसन: 135 x 240
| हामीसँग अहिले स्टकमा ESP32-PICO-V3-02 को 250 टुक्राहरू उपलब्ध छन्। | G15 | G13 | G14 | G12 | G5 | G27 |
| TFT डिस्प्ले | TFT_MOSI | TFT_CLK | TFT_DC | TFT_RST | TFT_CS | TFT_BL |
Microphone MIC (SPM1423)
| हामीसँग अहिले स्टकमा ESP32-PICO-V3-02 को 250 टुक्राहरू उपलब्ध छन्। | G0 | G34 |
| MIC SPM1423 | CLK | डाटा |
6-Axis IMU (MPU6886) & RTC BM8563
| हामीसँग अहिले स्टकमा ESP32-PICO-V3-02 को 250 टुक्राहरू उपलब्ध छन्। | G22 | G21 | G19 |
| IMU MPU6886 | SCL | SDA | |
| BM8563 | SCL | SDA | |
| आईआर एमिटर | TX | ||
| रातो एलईडी | TX |
HY2.0-4P
| HY2.0-4P | कालो | रातो | पहेंलो | सेतो |
| PORT.CUSTOM | GND | 5V | G32 | G33 |
मोडेल आकार
डाटाशीटहरू
हामीसँग अहिले स्टकमा ESP32-PICO-V3-02 को 250 टुक्राहरू उपलब्ध छन्।
ST7789V2 को परिचय
BM8563
MPU6886
SPM1423
सफ्टवेयरहरू
Arduino
StickC-Plus2 Arduino Quick Start
StickC-Plus2 Library
StickC-Plus2 Factory Test Firmware
UiFlow1 ले तपाईंलाई 100% सहयोग गर्नेछ।
StickC-Plus2 UiFlow1 Quick Start
UiFlow2 ले तपाईंलाई 100% सहयोग गर्नेछ।
StickC-Plus2 UiFlow2 Quick Start
प्लेटफर्म आईओ
[env:m5stack-stickc-plus2]
platform = espressif32@6.7.0
board = m5stick-c
फ्रेमवर्क = arduino
upload_speed = 1500000
monitor_speed = 115200
build_flags =
-DBOARD_HAS_PSRAM
-mfix-esp32-psram-cache-issue
-DCORE_DEBUG_LEVEL=5
lib_deps =
M5Unified=https://github.com/m5stack/M5Unified
USB चालक
Click the links below to download the driver that matches your operating system. The package contains CP34X drivers (for CH9102). After extracting the archive, run the installer that matches your OS bit-depth.
If you encounter issues such as timeout or “Failed to write to target RAM” during downloading, please try reinstalling the driver.
| चालकको नाम | Supported Chip | डाउनलोड गर्नुहोस् |
| CH9102_VCP_SER_Windows | CH9102 | डाउनलोड गर्नुहोस् |
| CH9102_VCP_SER_MacOS v1.7 | CH9102 | डाउनलोड गर्नुहोस् |
macOS Port Selection
Two serial ports may appear on macOS. Please select the port named wchmodem.
Easy loader
Easy Loader is a lightweight program flasher that comes with a demonstration firmware. By following a few simple steps, you can flash it to the controller for quick functional verification.
| Easy loader | डाउनलोड गर्नुहोस् | नोट |
| Factory Test for Windows | डाउनलोड गर्नुहोस् | / |
अन्य
StickC-Plus2 Restore Factory Firmware Guide
भिडियो
StickC-Plus2 Feature Introduction
StackC Plus2 视频.mp4
संस्करण परिवर्तन
| रिलीज मिति | विवरण परिवर्तन गर्नुहोस् | नोट |
| / | पहिलो रिलीज | / |
| 2021-12 | Added sleep and wake-up function, version updated to v1.1 | / |
| 2023-12 | Removed PMIC AXP192, MCU changed from ESP32-PICO-D4 to ESP32-PICO-V3-02, different power-on/off method, version v2 | / |
उत्पादन तुलना
हार्डवेयर भिन्नता
| उत्पादन नाम |
SoC | पावर व्यवस्थापन | ब्याट्री क्षमता | मेमोरी | USB-UART Chip | रङ |
| Stick C-Plus | ESP32-PICO-D4 | AXP192 | 120 mAh | 520 KB SRAM + 4 MB Flash | CH522 | Red- orange |
| StickC-Plus2 | हामीसँग अहिले स्टकमा ESP32-PICO-V3-02 को 250 टुक्राहरू उपलब्ध छन्। | / | 200 mAh | 2 MB PSRAM + 8 MB Flash | CH9102 | सुन्तला |
Pin Differences
| उत्पादनको नाम | IR | एलईडी | TFT | बटन ए | बटन बी | बटन सी (WAKE) |
होल्ड गर्नुहोस् | ब्याट्री भोल्युमtage पत्ता लगाउनुहोस् |
| M5STICKC PLUS | G9 | G10 | MOSI (G15) CLK (G13) DC (G23) RST (G18) CS (G5) |
G37 | G39 | नियमित बटन |
/ | Via AXP192 |
| M5STICKC PLUS2 | G19 | G19 | MOSI (G15) CLK (G13) DC (G14) RST (G12) CS (G5) |
G37 | G39 | G35 | G4 | G38 |
Power On/Off Differences
| उत्पादन नाम | पावर अन | पावर अफ |
| Stick C- Plus2 | Press “BUTTON C” for more than 2 s, or wake via RTC IRQ. After wake-up, set HOLD (G4)=1 in the program to keep power on, otherwise the device will shut down again. |
Without USB power, press “BUTTON C” for more than 6 s, or set HOLD (GPIO4)=0 in the program to power off. With USB connected, pressing “BUTTON C” for more than 6 s will turn off the screen and enter sleep, but not a full power- off. |
Because StickC-Plus2 removes the PMIC AXP192, the power-on/off method differs from previous versions. As mentioned at the beginning of this document, the operation is largely similar, but the supported libraries will differ. Wi-Fi and IR signal strength have both been improved compared to the previous model.
कागजातहरू / स्रोतहरू
 |
M5STACK ESP32-PICO-V3-02 IoT Development Module [pdf] प्रयोगकर्ता गाइड ESP32-PICO-V3-02 IoT Development Module, ESP32-PICO-V3-02, IoT Development Module, Development Module, Module |