OMRON DX शृङ्खलाको घटना ट्रिगर गरिएको भिडियो लगिङ प्याकेज

परिचय

• हाम्रो DX-श्रृंखला डाटा फ्लो कन्ट्रोलर खरिद गर्नुभएकोमा धन्यवाद।
• This manual provides information about the Event-triggered Video Logging Package included with the DX Series Data Flow Controller.
• Please read this manual and make sure that you understand the functionality and performance of the product before you attempt to use it in a control system.

अभिप्रेत दर्शक
This manual is intended for the following personnel, who must also have knowledge of electrical sys-tems (electrical engineers or the equivalent).

• Personnel in charge of designing and operating data utilization systems on a production site.
• Personnel in charge of designing and operating maintenance systems on a production site.

यो पुस्तिका पढ्नको लागि मार्गदर्शन
नियम र सर्तहरू सम्झौता, सुरक्षित प्रयोगको लागि सावधानीहरू, सही प्रयोगको लागि सावधानीहरू, र सम्बन्धित म्यानुअलहरूको बारेमा जानकारीको लागि, DX श्रृंखला डेटा प्रवाह नियन्त्रक प्रयोगकर्ताको म्यानुअल (V241-E1) हेर्नुहोस्।

संशोधन इतिहास
म्यानुअलको अगाडि र पछाडिको कभरमा रहेको क्याटलग नम्बरको प्रत्ययको रूपमा म्यानुअल संशोधन कोड देखिन्छ।

संशोधन कोड	मिति	संशोधित सामग्री
01	अक्टोबर २०२२	मौलिक उत्पादन

सुविधाहरू र प्रणाली कन्फिगरेसन

घटना-ट्रिगर गरिएको भिडियो लगिङ प्याकेजको क्षमताहरू

घटना-ट्रिगर गरिएको भिडियो लगिङ प्याकेज

• This package enables video recording of equipment behavior during abnormal events by retrofitting IP cameras and sensors. Traditionally, when equipment abnormalities occurred, maintenance personnel had to visit the site and visually inspect the equipment’s condition and operation. This process required significant time and effort for root cause analysis and recovery.
• With this package, sensors are installed to capture abnormal status signals output from devices such as PLCs, along with IP cameras. When an abnormal status signal is detected, the system records and stores video footage from before and after the event.
• पुनः द्वाराviewing the recorded video, users can visually confirm the equipment’s condition surrounding the abnormal event, allowing them to understand the situation before arriving on-site.
• This enables faster identification of root causes and reduces recovery time.
  

Exampप्रणाली कन्फिगरेसनहरू

सञ्चालन प्रक्रिया

यो खण्डले घटना-ट्रिगर गरिएको भिडियो लगिङ प्याकेजको सञ्चालन प्रक्रियाको वर्णन गर्दछ।

समग्र कार्यप्रवाह

• The following is the overall workflow for using the Event-triggered Video Logging Package.
• Refer to the manuals or instruction manuals of each device for wiring, installation, configuration, and software startup procedures.

Configuration of IP Camera

• This section describes the configuration procedures for IP cameras required for the Event-triggered Video Logging Package.
• It assumes that the system connections described in 1-2 Exampप्रणाली कन्फिगरेसनहरू पहिले नै पूरा भइसकेका छन्।

आईपी ​​क्यामेरा कन्फिगरेसन

1. Power on the PoE switching hub and IP camera, then connect the PC to the IP camera
2. Use the IP camera configuration tool on the PC to set the IP address of the IP camera.
   Refer to the IP camera manual and configure the settings as follows:
   IP ठेगाना: 192.168.250.xxx (Set xxx to any value that does not conflict with other devices)
   प्रयोगकर्ता नाम: जरा
   पासवर्ड: व्यवस्थापक
3. Adjust the installation position and angle of the camera to ensure the required video can be captured.

Starting the Event-triggered Video Logging Package

• ड्यासबोर्ड जेनेरेटरमा लग इन गर्नेदेखि SpeeDBee Synapse र Grafana मा सेटिङहरू लागू गर्नेसम्मका प्रक्रियाहरूका लागि, DX शृङ्खला ड्यासबोर्ड जेनेरेटर प्रयोगकर्ताको म्यानुअलमा रहेको खण्ड २-२ "ड्यासबोर्ड जेनेरेटर प्रयोग गर्ने" हेर्नुहोस्।
• यसले डेटा फ्लो कन्ट्रोलरमा जडान भएका उपकरणहरूको IP ठेगानाहरू कसरी दर्ता र कन्फिगर गर्ने भनेर व्याख्या गर्दछ।

कन्फिगरेसन प्रक्रिया

• तलका चरणहरू पालना गर्नुहोस्।
• This procedure assumes that the Dashboard Generator, Synapse, and Grafana are already integrated.

NX-OD (आउटपुट युनिट) कन्फिगरेसन

• Basic configuration of the NX Series Machine Automation Controller is omitted in this explanation. This section describes how to add variables in the I/O Map settings for NX-OD.
• If the variable name for the abnormal status used to control the alarm device in an existing PLC is already known, and the variable is configured as a global variable with network exposure enabled, the following steps are not required.

1. In Sysmac Studio, display the I/O Map of the NX-OD that outputs the abnormal status signal. Switch to offline mode to edit.
2. Confirm the Variable Name and Edit Type for the abnormal status output.
   यस मा पूर्वample, यो मानिन्छ कि असामान्य स्थिति संकेत आउटपुट सम्पर्क ०० मा आउटपुट छ। चर नाम Ch1Output मा सेट गरिएको छ, र चर प्रकार ग्लोबल चर मा सेट गरिएको छ।
3. Set the network exposure of the abnormal status output variable Ch1Output to Publish Only.
   Open the settings screen from the left tab: Programming → Data → Global Variables.
4. Switch to online mode and synchronize.
5. Click the Transfer to Controller Button.
   कार्यक्रम स्थानान्तरण गरिनेछ।
6. When prompted to switch to run mode, click the Yes Button.

उपकरण सूची स्क्रिन - उपकरण स्क्यान

1. Click the Device Scan Button at the top right of the Device List Screen.
   उपकरण स्क्यान स्क्रिन देखा पर्नेछ।
2. Select the interface from the dropdown menu.
3. When the Scan Button becomes active, click it.
4. The scanned devices will be displayed. Click the Apply Button. तपाईं उपकरण सूची स्क्रिनमा फर्कनुहुनेछ। उपकरणहरू अद्यावधिक गरिएको छ भनी पुष्टि गर्नुहोस्। उदाहरणमाample, NX102-9000 is added to Ethernet/IP.
   The scanned IP address of the IP camera will be displayed at the bottom under Ethernet.
5. Click the Edit Button on the row at the bottom of the Ethernet list where the scanned IP address of the IP camera is displayed.
   पूर्व माample, IP ठेगाना 192.168.250.66 हो।
6. From the Device Type dropdown menu, select Ethernet.
7. Enter a desired name in the Device Name field. Exampले: आईपी क्यामेरा
8. Click the Save Button.
   तपाईं उपकरण सूची स्क्रिनमा फर्कनुहुनेछ।

प्याकेज सूची स्क्रिन - ड्यासबोर्ड दर्ता

1. Click the Register Dashboard Button at the top right of the Package List Screen.
   दर्ता ड्यासबोर्ड स्क्रिन देखा पर्नेछ।
3. Configure the information on the Register Dashboard Screen.
   

   सेटिङ वस्तु	विवरण
   ड्यासबोर्डको नाम	Enter a desired name. It will be displayed in Synapse and Grafana. ExampLe: TEST
   प्याकेज	चयन गर्नुहोस् घटना-ट्रिगर गरिएको भिडियो लगिङ प्याकेज.
   उपकरण पहिचान	Optional input fields. Includes factory name, line name, process name, and equipment name.

   दर्ता बटन क्लिक गर्नुहोस्।
   कन्फर्म ड्यासबोर्ड दर्ता स्क्रिन देखा पर्नेछ।

4. दर्ता बटन क्लिक गर्नुहोस्।
   ड्यासबोर्ड दर्ता गर्न लगभग ३० सेकेन्ड लाग्छ।
   दर्ता पूरा भएपछि, प्रणाली ड्यासबोर्ड सूची स्क्रिनमा ट्रान्जिसन हुनेछ।

ड्यासबोर्ड सूची स्क्रिन - Synapse सुरु गर्दै

1. Click the SpeeDBee Synapse Button at the top right of the Dashboard List Screen.
   SpeeDBee Synapse स्क्रिन देखा पर्नेछ।
2. A panel has been added with a custom dashboard name (e.g., TEST).
   Click DETAIL on the corresponding panel.
   The screen will transition to the Synapse Connection Screen.
3. Change Run to Edit.
4. Delete the EtherNet/IP Collector Component and the NXR_dr_trigger Component.
5. From the tab on the left, select EtherNet/IP Collector and place it.
6. Configure the placed EtherNet/IP Collector.
   

   वस्तु	विवरण
   नाम	घटकको नाम। उदाहरणampले: त्रुटि_सिग्नल_कलेक्टर
   होस्ट	The IP address of the host. Set the IP address of the NX102-9000. Exampले: 192.168.250.1
   Get Interval	The data acquisition interval. Set to 100 ms.

   

7. Click the ADD Button to continue configuration.
8. कन्फिगरेसन पछि, बचत बटनमा क्लिक गर्नुहोस्।
   

   वस्तु	विवरण
   चर नाम	NX-OD चर सेट गर्नुहोस्। उदाहरणampले: Ch1आउटपुट
   स्तम्भ नाम	अधिग्रहण स्तम्भको नाम। उदाहरणampले: डेटा
   डेटा प्रकार/एरे आकार	Set the data type of the variable Ch1Output. Exampले: बुल, १

   8 Connect the output port on the right side of the created component to the input port on the left side of the Event trigger. 9 Connect the output port on the right side of the created component to the input port on  the left side of the Event Recorder.

9. क्लिक गर्नुहोस्  Button on the VIDEO Collector Component.
10. Modify the contents of RTSP URL IP क्यामेराको IP ठेगानासँग मिलाउन।
    पूर्व माampतल, निम्न परिवर्तन गरिएको छ: rtsp://root:admin@192.168.250.67/axis-media/media.amp ↓ rtsp://root:admin@192.168.250.60/axis-media/media.amp
11. Click the TEST Button.
12. The camera will start.
13. Click the CLOSE Button.Return to the previous screen.
14. Click the SAVE Button.
15. क्लिक गर्नुहोस् the Button on the VIDEO Collector Component. छोटो पर्खाइ पछि, प्रवाह लिङ्क पहेंलोबाट हरियोमा परिवर्तन हुनेछ।
16. क्लिक गर्नुहोस् on the following two components:
    इथरनेट/आईपी कलेक्टर र घटना ट्रिगर
17. क्लिक गर्नुहोस् Button on the Event trigger Component.
18. In the component settings, configure the name assigned to the Ethernet/IP Collector.
    कन्फिगरेसन पछि, बचत बटनमा क्लिक गर्नुहोस्।
    यस मा पूर्वampले, चरण ५ मा सेट गरिएको घटक नाम Error_signal_collector प्रयोग गरिएको छ।
19. Click the STOP Button, then click the START Button to restart.
20. Right-click the input port of the Event Recorder Component.
21. Configure In port setting:
    कार्यक्रम प्रयोग गर्नुहोस्
    • Acquisition range pre event occurrence(sec): Modify as needed (e.g., 10 seconds)
    • Acquisition range post event occurrence(sec): Modify as needed (e.g., 10 seconds)
      घटना पत्ता लगाउने र रेकर्डिङ गर्ने बीच समय अन्तराल हुने भएकोले, सुरुवात घटनाभन्दा पहिले लामो अवधि सेट गर्नुहोस्। विशेष गरी, वास्तविक रेकर्डिङ समयमा लगभग ३ सेकेन्ड थप्नुहोस्।
      कन्फिगरेसन पूरा भएपछि, बचत बटनमा क्लिक गर्नुहोस्।
22. क्लिक गर्नुहोस् on the Event Recorder Component. पूर्वनिर्धारित अवधारण समय १६८ घण्टा (एक हप्ता) हो। आवश्यकता अनुसार परिमार्जन गर्नुहोस्, त्यसपछि बचत गर्नुहोस् बटनमा क्लिक गर्नुहोस्। सही प्रयोगको लागि सावधानीहरू
    डाटा भण्डारण स्थान
    Always use an external USB memory device with a capacity of 2GB or more.
    The internal memory of the Data Flow Controller does not have sufficient capacity, and event videos cannot be saved.
    Refer to section 2-5 Changing the Data Storage Location in the DX Series Dashboard Generator User’s Manual for configuration steps.
23. Click the on the Event Recorder Component.
24. Click the START Button.
25. Click the System Tab at the top left (for Error Manager configuration). The System Panel will appear.
26. क्लिक गर्नुहोस् (Launch) Button on the Error Manager Component. The Error Manager will start. नोट: Error Manager is required for Grafana to retrieve data from Synapse.

ड्यासबोर्ड सूची स्क्रिन - ग्राफाना सुरु गर्दै

1. Click the graph icon in the upper-right corner of the Synapse Screen. The Grafana Screen will appear.
2. Click Dashboards. The screen switches.
3. Click any dashboard name that has been added. ExampLe: TEST
4. Click Event-triggered Video Logging Package. The screen switches.
5. The KPI is displayed as a graph. To change the time range on the horizontal axis, use the dropdown menu labeled Last 1 hour JST. यस मा पूर्वampले, अन्तिम ५ मिनेट चयन गरिएको छ। नोट: The vertical axis (values) of the graph automatically adjusts its scale based on the range of acquired data.
6. A graph with the updated time range on the horizontal axis will be displayed. To adjust the data refresh frequency, click Refresh Button at the top right. Select the desired interval from the dropdown menu.

कार्यक्रम भिडियोहरूको प्लेब्याक
यो खण्डले घटना भिडियोहरू प्ले ब्याक गर्ने प्रक्रियाको वर्णन गर्दछ।

1. क्लिक गर्नुहोस् viewSpeeDBee Synapse प्यानलको माथिल्लो दायाँमा रहेको er आइकन।
2. Click Event Record.
3. Click on the desired recorded data from the list. Click ► to start playback.

• For details on the video playback feature, refer to the i-Trigger Operation Guide for SpeeDBee Synapse: https://www.saltyster.com/ss-docs/speedbeesynapse/i-trigger/viewer.html
• OMRON निगम औद्योगिक स्वचालन कम्पनी
• क्योटो, जापान
• सम्पर्क: www.ia.omron.com
• Contact for inquiries for this product (only for DX-series)
• DataPF-contactdesk-OC@omron.com मा सम्पर्क गर्नुहोस्।
  सञ्चालन समय: ९:०० देखि ५:०० सम्म (शनिबार, आइतबार र डिसेम्बर ३१ देखि जनवरी ३ सम्म बाहेक), JST
• ट्यूटोरियल भिडियो https://www.fa.omron.co.jp/dx1/video-manual/en/

नोट

1. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written permission of OMRON.
2. No patent liability is assumed with respect to the use of the information contained herein.
   Moreover, because OMRON is constantly striving to improve its high-quality products, the information contained in this manual is subject to change without notice.
3. Every precaution has been taken in the preparation of this manual. Nevertheless, OMRON assumes no responsibility for errors or omissions.
   Neither is any liability assumed for damages resulting from the use of the information contained in this publication.

ट्रेडमार्कहरू

• ODVA, CIP, CompoNet, DeviceNet, र EtherNet/IP ODVA का ट्रेडमार्कहरू हुन्।
• The SD and SDHC logos are trademarks of SD-3C, LLC.
• SpeeDBee Synapse is a trademark of SALTYSTER Co., Ltd.
• Grafana is a trademark of Grafana Labs.

प्रतिलिपि अधिकार
This product incorporates certain third party software. The license and copyright information associated with this software is available at https://www.fa.omron.co.jp/product/tool/dx-info/index_en.html

FAQ

Can I use the Event-triggered Video Logging Package with other controllers?

The Event-triggered Video Logging Package is specifically designed for use with the DX Series Data Flow Controller and may not be compatible with other controllers.

How do I update the firmware of the DX Series Data Flow Controller?

Firmware update instructions can be found in the DX Series Data Flow Controller User's Manual. Follow the provided guidelines to update the firmware safely.

कागजातहरू / स्रोतहरू

OMRON DX शृङ्खलाको घटना ट्रिगर गरिएको भिडियो लगिङ प्याकेज [pdf] प्रयोगकर्ता पुस्तिका N704-E1-01, 1025, DX शृङ्खला घटना ट्रिगर गरिएको भिडियो लगिङ प्याकेज, DX शृङ्खला, घटना ट्रिगर गरिएको भिडियो लगिङ प्याकेज, ट्रिगर गरिएको भिडियो लगिङ प्याकेज, भिडियो लगिङ प्याकेज, लगिङ प्याकेज

सन्दर्भहरू

• प्रयोगकर्ता पुस्तिका