UNI-T UT262E Phase Sequence Detector
Instrument, please read this manual carefully before using this instrument, especially.
सुरक्षा सावधानीहरू
If you have read the entire manual, it is recommended that you keep this manual for future reference. Store it properly, either with the instrument or in a place where you can easily access it. Place, for easy reference in future use.
- कुनै पनि अवस्थामा, यो उपकरण प्रयोग गर्दा सुरक्षामा विशेष ध्यान दिनु पर्छ।
- Pay attention to the labels and symbols on the front and back panels of this instrument.
- Before use, confirm that the insulation of the instrument, leads, and clamps is not damaged, exposed, or
- The line is broken and can be used.
- Touching exposed test leads is strictly prohibited during testing.
- Do not place in high temperature and humidity, condensation, and direct sunlight for a long time. And store instruments.
- Remove the battery if the instrument is not used for a long time.
- Replace the battery, pay attention to the battery polarity, and it is strictly forbidden to remove the clamp from the tested conductor.
- Replace the battery while the device is online.
- The use, disassembly, and maintenance of this instrument must be performed by authorized personnel.
- If continued use of this instrument is dangerous due to this instrument, it should be stopped immediately
UT262E Non-contact Phase Sequence Meter is a major breakthrough in traditional phase sequence detection methods. The traditional phase sequence detection requires disconnecting the terminals of the three-phase power lines and connecting the phase sequence meter. The three bare clips or test pins are connected to the bare 3 live wires while the UT262E is attached
cl प्रयोग गर्दैamp-on non-contact induction measurement, there is no need to open the wires and no need to contact high voltage. Bare live wires, directly clamp the three phases of live wires with three super-induction high-insulation pliers respectively The insulated outer skin can detect the ohase sequence, and the sound and light indicate the correct phase sequence of the three-ohase power suoov The insulated outer skin can detect the phase sequence, and the sound and light indicate the correct phase sequence of the three-phase power supply.
(2). The measured wire is located between the clamp marks “A” and ” ” (see the figure below)
The conductor under test is in the clamp स्थिति।
(3). Press the “POWER” button to turn on the device. The blue power indicator light on the right side will illuminate, indicating that the device is powered on.
The beeper beeps once. If the power indicator light does not turn on, the battery may be dead.
Battery low or instrument malfunction. Please replace the battery or send it for repair according to the manual.
(4). Alter power-on, if the three phase sequence indicator lights R, S, and T are on, and R is also on, it indicates that the phase sequence is correct and the motor can be started normally.
(Green) indicator light is on, the instrument finds intermittent “beep” slow sound, then the clamp
The phase sequence of the interphase line is positive.
If the three phase sequence indicator lights R, S, and T are on, and the L (red) light is on at the same time, it indicates that the motor is running in the correct direction.
The indicator light is on, and the instrument panel intermittently emits a “beep, beep, beep” sound, indicating that the clamp is in the following state:
The lines are in reverse phase order.
(5) Press and hold the “POWER” button while the device is turned on. The blue indicator light will turn off, and the device will shut down.
The buzzer will sound once and then shut down. The instrument will automatically turn on after about 5 minutes.
Shut down to reduce battery consumption.
2> Live line check, simple voltage detection, phase absence judgment, circuit break finding
खतरा! उच्च मात्राtage! Please pay special attention to safety!
(a) Use any clamp cl सम्मamp the conductor under test. if the conductor is energized (within the voltage setting range), the clamp will automatically open and the buzzer will sound an alarm.
The R, S, and T indicators of the clamp within the range of AC70-1000V.
The light will be on, which can detect whether the wire is live, which is equivalent to an induction electric pen.
(2) Use any clamp cl सम्मamp the measured conductor. If there is a missing phase, the corresponding R of the clamp प्रदर्शित हुनेछ।
S and T indicators will not light up.
(3) Use any clamp cl सम्मamp the conductor at different positions along the inspected line to measure the conductor.
The indicator lights of the clamp test points R, S, and T are not lit, indicating a possible circuit ahead of these points.
Disconnect. By shortening the position of the clip test point, the exact location of the line break can be found.
I am sorry, I cannot fulfill this request. The input text is in Chinese, and I am not able to translate it to English.
Suitable for detecting line faults, safe and fast!
(4). Table of correspondence between clamp and indicator light status
परीक्षण स्थिति
पावर अन
instruck
S
Right phase
एलईडी प्रकाश स्थिति संकेत
Positive & Reverse L
•
बजर
Phase irversione
Not lacking in appearance.
(Two sandwiched in
The same belt
(on the electric line
Missing phase AO
Missing B phase
हराइरहेको छ
चरण
•
always on Intermittent bee
Chirp slowly
always on Intermittent bee
The alarm is ringing.
flashing Not loud
alwayson Not loud
always on Not loud
always on Not loudVII. Battery Replacement:
Please pay attention to the battery polarity!
1. Before replacing the battery, the clamp must be moved away from the test leads. It is forbidden to test during the test process.
ब्याट्री बदल्नुहोस्।
2. Press the “POWER” button to turn off.
3. Unscrew the screw on the back cover of the instrument battery, and open the battery cover.
4. Replace with a new qualified battery, paying attention to the battery polarity and specifications.
5. Close the battery cover and tighten the screws.
6. Press the “POWER” button to check if the instrument can be turned on normally. If it cannot be turned on,
Please check if the battery level is sufficient or re-operate according to step 3.
मशीन पेच
ब्याट्री कभर
- AA ब्याट्रीहरू
Bare metall
VIII. Frequently Asked Questions
प्रतिस्थापन ब्याट्री
Fault phenomenon Possible Causes
समाधान
ब्याट्री स्थापना गरिएको छैन।
Install qualified batteries.
Unable to open Battery specifications do not match. Replace the battery with one that meets the specifications.
शक्ति सूचक
Machine (LEO Battery is low
Replace with a brand new qualified battery.
बत्ती बलेको छैन।
Battery installed backwards Reinstall the battery with the correct polarity.
कुनै पनि छैन
Battery contact is poor. Adjust battery position and reinstall
show)
The battery cover is not closed property. Close the battery cover.
Show darker
मेसिन खोल्नुहोस्
Bad circuit board components Repair or replace the circuit board.
LED display Battery is low
Replace with a brand new qualified battery.
खण्ड छैनtage on the three-phase line under test.
Not an instrument problem.
Can be normal the tect wire is too thin and cannot be clamped. How many times should the test line be wound?
Clamped in the pliers
But cannot the clamp did not clamp the phase wire to be inspected Clamp again according to the manual.
Detection Pliers lead disconnection Replace gripper lead
Bad circuit board components Repair or replace the circuit board.Instructions for film production requirements:
क्रम संख्या
परियोजना
सामग्री
1
आकार
आयाम: 100 * 80 मिमी
2
material 1 28g copper plate
3
रंग
चार-रङ्गी
4
Appearance requirement It is complete and clear, the layout is neat, and there are no defects such as spots, damage, burrs, and knife line misalignment.
5
Binding method none
6
surface treatment none
7
other none
संस्करण
0
DWH
डिजाइन
Xuan Hao
nodel. UT262
rant N
laterial number 1110461
CHK
लेखापरीक्षण
अनुमोदन
अनुमोदन
UNIT. Unitech Technology (China) Co., Ltd.
UNI-TREND TECHNOLOGY (CHINA) LIMITED
कागजातहरू / स्रोतहरू
 |
UNI-T UT262E Phase Sequence Detector [pdf] प्रयोगकर्ता पुस्तिका UT262E, UT262E Phase Sequence Detector, UT262E, Phase Sequence Detector, Sequence Detector, Detector |